产品规格: | 不限 | 产品数量: | 不限 |
---|---|---|---|
包装说明: | 按订单 | 价格说明: | 不限 |
查看人数: | 207 人 | 本页链接: | https://info.b2b168.com/s168-107476731.html |
河北专业生产各型号厢式压滤机、板框压滤机、隔膜全自动压滤机、快开式隔膜压滤机、ju bing烯压滤机(化工行业压滤机、洗煤压滤机、铁矿压滤机、淀粉压滤机、金矿行业压滤机、尾矿处理压滤机、酒精行业压滤机、污水处理压滤机)以及配套压滤机入料泵、渣浆泵、防腐泵、耐酸泵(玻璃钢泵、不锈钢泵)、压滤机滤板、夹布器、把手等压滤机配件。)
Hebei specializes in producing various types of box filter presses, plate-and-frame filter presses, diaphragm full-automatic filter presses, quick-opening diaphragm filter presses, ju propylene filter presses ( chemical industry filter presses, coal washing filter presses, iron ore filter presses, starch filter presses, gold mine filter presses, tailings treatment filter presses, alcohol industry filter presses, sewage treatment filter presses ) and filter press accessories such as feed pumps, slurry pumps, anti-corrosion pumps, acid-resistant pumps ( glass fiber reinforced plastic pumps, stainless steel pumps ), filter press plates,ZJW压滤机**泵厂家@压滤机**泵选型厂家, cloth clamps, handles and the like. )
压滤机入料泵的注意事项有哪些? 机械密封渣浆泵,一般是对密封要求比较高的情况使用。特别是一些化工,食品领域,不仅要求密封,而且较主要是不允许加入额外成分进入泵体。缺点就是,成本高,维修困难等。 What are the precautions for the feed pump of the filter press? Mechanical seal slurry pumps are generally used in situations where sealing requirements are relatively high. Especially in some chemical and food fields, sealing is not only required, but also additional components are not allowed to enter the pump body. The disadvantages are high cost and difficult maintenance.
SYA ZJW ZJE压滤机入料选泵压滤机入料泵与其它一般性输送用泵区别很大,一般性输送用泵的选型,主要是选用某条流量,扬程曲线上的某一点或很短一段曲线所对应的性能。而压滤机的工作特性是:滤室内滤饼的逐渐形成,入料阻力也随之加大,要求入料泵从起始时的大流量、低扬程自行过渡末期的小流量,高扬程。反映到曲线上是需要较长的甚至一条较完整的而且是越 陡越好的流量、扬程曲线。除此特性外,还要求泵工作在高压时,不用轴封水和无泄 漏,为建设环保工厂创造条件。压滤机入料泵
SYA ZJW ZJE filter press feed selection pump {fine} is very different from other general conveying pumps. The selection of general conveying pumps mainly depends on the performance corresponding to a certain flow rate, a certain point on the head curve or a very short section of the curve. The working characteristics of the filter press are as follows: the filter cake in the filter chamber is gradually formed, and the feed resistance is also increased, requiring the feed pump to start with a large flow, a small flow at the end of the low head self-transition, and a high head. Reflected on the curve, it needs a longer or even a more complete flow and head curve, and the steeper the better. In addition to this characteristic, the pump is required to work at high pressure, without shaft sealing water and leakage, to create conditions for the construction of environmental protection factories. {Jing}
SYA ZJW ZJE压滤机入料选泵 压滤机入料泵配置功率入料泵的ZUIDA功率损耗在入料的初始阶段,所以要详细计算由入料泵往压滤机注浆的ZUI小压力,然后按ZUIXIAO压力对应的该泵的流量、扬程配用功率,如此较为准确、节约。由于各工厂压滤系统的实际布置差异,当入料泵与滤机之间的沿程阻力较大时(如:泵距压滤机较远、管道直径偏小、弯头与闸门较多、浆液粘度较大等),会增加入料泵的扬程损失,降低成饼压力。滤饼水份偏高与单循环时间拉长,导致系统的生产效率大为降低,所以必须要合理的管路配置。压滤机入料泵
压滤机入料泵怎么拆开维修,拆开后如何装配,
准备工具、物料
公制梅花/开口扳手一套、轴承拉拔器(常见三角拉马)、磁力百分表、外径千分尺、卡尺、塞尺、直角尺、铜棒、加柄起子、锤子、同规格V型铁2块、清洗煤油及油盆、棉纱等;
压滤机入料泵拆装工具三角拉马
拆泵注意事项
1、压滤机入料泵拆前确保泵内液体排放干净,如果拆转子,转子轴承箱内的润滑油应排放干净,如果是新加的油存起来,维修后继续使用,不要直接倒掉;
2、对于时间久太紧或生锈,造成不好拧开的螺丝,可用提前准备的煤油润滑螺母,或木锤轻敲螺母再拆卸,其他部位也可采用该方法;
3、对于重要部件提前做好标记,以免复位时出错,接合面和易碰伤的部件应妥善保存好,防止损坏;
4、拆下来的垫片如果损伤严重应更换新垫片,拆除的零部件应用煤油清洗后再进行装配