供应PT06 10 15MM西班牙电位器家电仪器控制插件西班牙电位器

Ａ。电气性能Electrical specifications
1	总阻值
Total Resistance	电位器1～3端全部电阻值。
Measurement shall be made by the resistance between terminal R1and R3.	20K
2	阻值线性
Resistance taper	电阻值变化规律
Resistance changes	直线 B
（line）
3	总阻值允许差Total Resistance toleranc	电位器1～3端总阻值之公差。
Measurement shall be made by the resistance  tolerance between terminal R1 and R3.	  ± 10 % 
4	额定功率
Rated power	电位器1～3端能连续承受之较大之功率Rated power is based on continuous full load operation at the maximum voltage between terminal R1 and  R3.	0.15W(50℃)

5	残留电阻Residual resistance	电位器1～2端（将轴心旋转至1端底部测）及2～3端（将轴心旋转至3底部测）残留Test residual resistance beteen terminal R1 andR2;terminal R2 andR3	≤0.1%R

6	转动噪声
rotation of noise	轴心从电位器1端以30转/分匀速旋转至
3端时电位器所呈现之杂音情况
The murmur will appear when shaft turn from terminal 1 to terminal 3 by 30 rounds/minute equably speed.	≤47mV
7	有效电阻角度Electrical Rotation angle	电阻有效变化角度
Resistance effective changes in perspective	220°±20°
8	较高使用电压
Max operating voltage	电位器R1－R3端所承受的较大电压
Maximal voltage which sustained by terminal R1 and  R3	200V  DC

Ｂ。机械性能Mechanical specifications
1	旋转角度Total rotation angle	指轴置于1端较底部转往3端较底部之旋转角度The angle is measured by rotating shaft from the end of terminal R1 to the end of terminal R3.	 235°±10°
2	回转力矩Rotation torque	指轴在周围温度5°C～35°C以每秒钟60°匀速转动所需之力矩
Rotational torque when turn the shaft :without special provision,rotational speed is 60°/s in ambient temperature 5-35°C	0.4-1.2Ncm
3	止档强度Stop torque	轴从1端转至止档点或从3端转至止档点10秒后直至破坏之力量
The force that shaft transfer from terminal 1 to stop point or terminal 3 to stop point after 10 seconds until be break	>5Ncm
 

Ｃ。其它 Other
1	使用寿命Rotation life	经过10，000旋转测试后，总阻变化不**过±（15%R+0.5Ω)转动噪声不大于100mv
After 10,000 rotation after the test, the changes impacted no more than ± (15% R +0.5 Ω) rotational noise of not more than 100 mv	
2	端子强度
Terminal strength	经过焊接（350℃，3,5秒）后端子不得有接触不良或松动现象
After welding (350 ℃, 3,5 seconds) after the termination of terminal contacts should be good, no loosening of	
3	可焊性Soldering ability	260℃ ±5℃，持续时间2S ±0.5S，焊锡覆盖面积大于90%以上。
Dip the terminals into tin tank at 260℃±5℃ for 2±0.5 seconds, the soldering area should be more than 90%.