96通道50GHz 有热 AWG

产品概述/Product Overview

Here presents the generic specification for the 96 channel 50GHz Thermal AWG MUX/DEMUX component supplied by Flyin for use in DWDM system.

This product is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the AWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the AWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. 
 
 

 

极限条件/Absolute Maximum Ratings (unless otherwise specified)

参数/Parameters
 条件/Conditions
 规格/Specifications
 单位/Units
 
 
  
 较小/Min.
 较大/Max.
 
工作温度/Operating Temperature
 产品正常工作时/Operating
 -5
 65
 oC
 
工作湿度/Operating Humidity
 产品正常工作时/Operating
 5
 95
 %RH
 
存储温度/Storage Temperature
 产品不工作时/Non_Operating
 -40
 +85
 oC
 
存储湿度/Storage Humidity
 产品不工作时/Non_Operating
 5
 95
 %RH
 
光性能/Optical Specification (平**有热AWG/ Flat top Thermal AWG)

参数/Parameters
 条件/Condition
 规格/Specs
 单位/Units
 
Min
 Typ
 Max
 
通道数/Number of Channels
  
 96
  
 
通道间距/Number Channel Spacing
 50GHz
 50
 GHz
 
中心波长/Cha. Center Wavelength
 ITU频率/ITU frequency.
 C -band
 nm
 
通带频率/Clear Channel Passband
  
 ±6.25
 GHz
 
波长精度/Wavelength Stability
 Maximum range of the wavelength error  of all channels and temperatures in average polarization.
 ±0.05
 nm
 
-1 dB 带宽/-1 dB Channel Bandwidth
 Clear channel bandwidth defined by passband shape. For each channel
 XX
  
  
 nm
 
-3 dB 带宽/-3 dB Channel Bandwidth
 Clear channel bandwidth defined by passband shape. For each channel
 XX
  
  
 nm
 
插损/Optical Insertion Loss at ITU grid
 Defined as the minimum transmission at ITU wavelength for all channels. For each channel, at all temperatures and polarizations.
  
 6.0
 7.5
 dB
 
相邻通道隔离度/Adjacent Channel Isolation
 Insertion loss difference from the mean transmission at the ITU grid wavelength to the

highest power, all polarizations, within the ITU band of the adjacent channels.
 25
  
  
 dB
 
非相邻通道隔离度/Non-Adjacent, Channel Isolation
 Insertion loss difference from the mean transmission at the ITU grid wavelength to the

highest power, all polarizations, within the ITU band of the nonadjacent channels.
 30
  
  
 dB
 
总隔离度/Total Channel Isolation
 Total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of all other channels, including adjacent channels.
 22
  
  
 dB
 
插损一致性/Insertion Loss Uniformity
 Maximum range of the insertion loss variation within ITU across all channels, polarizations and temperatures.
  
  
 1.5
 dB
 
方向性/ Directivity(Mux Only)
 Ratio of reflected power out of any channel(other than channel n)to power in from the input channel n
 40
  
  
 dB
 
插损平坦度/Insertion Loss Ripple
 Any maxima and any minima of optical loss across ITU band, excluding boundary points, for each channel at each port
  
  
 0.5
 dB
 
回损/Optical Return loss
 Input & output ports
 40
  
  
 dB
 
PDL/Polarization Dependent Loss in Clear Channel Band
 Worst-case value measured in ITU band
  
 0.3
 0.5
 dB
 
偏振模式色散/Polarization Mode Dispersion
  
  
  
 0.5
 ps
 
较大承受光功率/Maximum Optical Power
  
  
  
 23
 dBm
 
功率监控范围/MUX/DEMUX input/ output

Monitoring range
  
 -35
  
 +23
 dBm
 

1.        IL Represents the worst case over a +/-0.1nm window around the ITU wavelength ；

2.        PDL was measured on average polarization over a +/- 0.1nm window around the ITU wavelength.



机械尺寸/Mechanical Schematic and Dimensions

尺寸/Dimensions
 428*251*43.7
 mm
 
光纤类型/Fiber Type
 公共端Common G657A fiber with 900mm loose tube，加900mm 套管，通道端G652D Ribbons Channels
 
光纤编排/Fiber Format
 4x 12带纤/4x12-fiber ribbons
 
光纤长度/Fiber Length
 输入端/Common
 1000mm ± 50mm with 900um loose tube/输入线长1000mm ± 50mm带900um套管
 
输出端/Channels
 Ribbon 500mm± 20 mm and Fan out 500mm± 30mm with 900um loose tube

/输出带纤500mm± 20 mm，加分支器线长500mm± 30mm
 
公共端/Common
 颜色/Color
 白/white
 
带纤标识/Ribbon Identification
 带纤末端贴数码贴标识

/Label with ribbon number to be placed midway between ribbon end-points
 
连接器类型/Connector Options
 Common
 LC/UPC
 
Channels
 LC/UPC
 
带纤光纤标识/Fiber Identification in Ribbon
 1
 蓝/Blue
 2
 橙/Orange
 3
 绿/Green
 4
 褐/Brown
 5
 灰/Grey
 6
 白/White
 
7
 红/Red
 8
 黑/Black
 9
 黄/Yellow
 10
 紫/Purple
 11
 粉/Pink
 12
 水/Aqua
 


 
                

 

电子规格/Electrical Specifications

Only for the thermal AWG module which has an internal temperature control circuit.

NO.
 Parameters
 Notes
 Specifications
 Units
 
Min
 Typ
 Max
 
2.23
 Set-Point temperature of component
 Optimum operating temperature section for thermal AWG

The commands could only set current temperature and threshold in this range.
 65
  
 90
 °C
 
2.24
 Set-Point temperature stability
 Over entire operating temperature range for thermal AWG
  
  
 ±0.5
 °C
 
2.25
 Heater Drive Voltage
  
  
 +5
  
 V
 
2.26
 Heater Drive Current
  
  
  
 2.5
 A
 
2.27
 Heater Power Dissipation(maximum, stable)
  
  
  
 12.5
 W
 
2.28
 Heater Power Dissipation(stable state)
 25°C ambient temperature
  
  
 6
 W
 
2.29
 AWG Temperature Settling Time
 AWG warm up time from a cold start(25°C ambient temperature) to set point for thermal AWG
  
  
 7
 min
 
2.30
 AWG Temperature Settling Time
 AWG warm up time from a cold start(-5°C ambient temperature) to set point for thermal AWG
  
  
 15
 min
 

Temperature control IC build inside

电接口/Electric interface

Connector type: 10 pin FRC box type (2.54mm pitch) male connector.

Pin definition is as below:


NO.
 pin#
 Signal Name
 Type
 Direction
 Descriptions
 
2.31
 1
 +5V
 Power
 ----
 supply for Heater circuit
 
2.32
 2
 +5V
 Power
 ----
 supply for Heater circuit
 
2.33
 3
 +5V
 Power
 ----
 supply for control circuit
 
2.34
 4
 Ready
 TTL
 Output
 ※         Set HIGH when the internal temperature is at a set-point temperature.

※         Set LOW when the internal temperature is not at a set-point temperature (higher than the Upper Temperature Threshold or lower than the Under Temperature Threshold).

※         This ** should be 3.3V TTL level.
 
2.35
 5
 Alarm
 TTL
 Output
 ※         Set HIGH when the internal temperature is higher than the set-point temperature.

※         Set LOW when the internal temperature is not higher than the set-point temperature.

Pin4 and pin5 could be used to check the temperature’s status.

※         This ** should be 3.3V TTL level.
 
2.36
 6
 Enable
 TTL
 Input
 ※         If set HIGH, the heater circuit is activated.

※         If set LOW, the heater circuit is disabled.

※         This ** should be 3.3V TTL level.
 
2.37
 7*
 TX
 TTL
 Output
 RS232 transmit **

This ** should be 3.3V TTL level.
 
2.38
 8
 GND
 Power
 ----
 Ground
 
2.39
 9*
 Rx
 TTL
 Input
 RS232 receive **

This ** should be 3.3V TTL level.
 
2.40
 10
 GND
 Power
 ----
 Ground
 

*: Information available for inquiry includes Chip Temperature, Module Status, P/N & SN.

可靠性说明/Reliability Specifications

The planar DWDM components described within this datasheet are fully qualified according to Telcordia reliability assurance requirements for fiber optic and opto-electronic components (GR-1221-CORE/UNC, Generic Reliability Assurance Requirements for Fiber Optic Branching Components, and Telcordia TR-NWT-000468, Reliability Assurance Practices for Opto-electronic Devices). The reliability report is available for request.
 

 

订购信息/Ordering Information

AWG
 X
 XX
 X
 XXX
 X
 X
 X
 XX
 
 
 Band
 Number of Channels
 Spacing
 1st Channel
 Filter Shape
 Package
 Fiber Length
 In/Out Connector
 
C=C-Band

L=L-Band

D=C+L-Band

X=Customize
 16=16-CH

32=32-CH

40=40-CH

48=48-CH

96=96-CH

XX=Special
 1=100G

2=200G

5=50G

X=Special
 C60=C60

H59=H59

C59=C59

H58=H58

XXX=special
 G=Gaussian

B=Broad Gaussiar

F=Flat Top
 M=Module

R=Rack

X=Special
 1=0.5m

2=1m

3=1.5m

4=2m

5=2.5m

6=3m

S=Specify
 0=None

1=FC/APC

2=FC/PC

3=SC/APC

4=SC/PC

5=LC/APC

6=LC/PC

7=ST/UPC

S=Specify