产品规格: | 不限 | 产品数量: | 不限 |
---|---|---|---|
包装说明: | 按订单 | 价格说明: | 不限 |
查看人数: | 104 人 | 本页链接: | https://info.b2b168.com/s168-95123931.html |
水下封堵
带压开孔机通用说明 带压开孔机通用说明:
1、将带压开孔机插好电源,打开电机开关, 检查设备运转情况,确认运转正常后,关机。 2、将带压开孔机底座上的V形铁骑附在管道上,然后调整链条的长度,并用插销定位,然后紧固链条另一端的螺母,使本机牢固地定位在管道上。 3、按规定确认带压开孔直径,水下封堵技术,装夹合适的带压开孔器。 4、动电机,再次确认带压开孔机,带压开孔器运转正常。 5、扳动(压下)带压开孔机手柄,使带压开孔器徐徐向下,水下封堵, 接近管子时,察看带压开孔位置是否正确;反之,应关机并重新调整位置后再开机。
General description of pressure hole opener general specification for pressure hole opener:
1. Plug in the power supply, turn on the motor switch, check the operation of the equipment, confirm the normal operation, shut down. 2, the V - shaped iron riding on the base of the pressure opener is attached to the pipe, then the length of the chain is adjusted, and the bolt is psitioned with the bolt, and then the nut on the other end of the chain is fastened so that the machine is firmly ositioned on the pipe. 3. According to the regulations,水下封堵哪家强, confirm the diameter of the opening with pressure and install the suitable pressure opener. 4, motor, reconfirm the pressure hole opener, the pressure opener operates normally. 5, wrench (press down) with pressure opener handle, so that the pressure opener slowly down, close to the pipe, look at the psition of the hole is correct; conversely, the machine should be shut down and reosition the osition and then start the machine.
水下封堵
不同管道封堵技术特点
1)筒式封堵 管道筒式封堵适用于管道内壁结垢、腐蚀的管线以及不规格变形管道,水下封堵服务,一般用于油田、石化系统的生产管线。该工艺具有封堵严密,不受管道年限的限制。
2)盘式封堵 管道盘式封堵适用于管道标准而且管道内壁没有结垢、腐蚀的长输管道,大多用于输送石油、成品油的长输管道,以及管道的抢修工作。该工艺具有封堵严密、承压高、施工快的特点。6 、管道带压开孔、封堵应用1)更换一段管道 2)管线改线3)、管道需要加设阀门
Characteristics of different pipe plugging technology
1) tube type plugging pipe type plugging is suitable for pipe lining and corrosion of pipeline and non specification deformation pipeline, which is generally used in oil field and petrochemical production pipeline. The process has a tight seal and is not subject to the limitation of pipeline age.
2) disc plugging pipe disc plugging is suitable for pipeline standard and long distance pipeline with no scale and corrosion on the inner wall of the pipe. Most of the pipeline is used for transporting oil, natural gas and finished oil, as well as the repair work of pipeline. The technology has the characteristics of tight plugging, high pressure and quick construction. 6, pipe pressure hole, plugging application 1) replace a section of pipe 2) pipeline permanent change line 3), pipeline need to add valve.